Roof Snow Load Calculator
Snow looks light — until a roof is holding tons of it. Estimate the load on your roof two ways.
Estimated load on your roof
21 lb/ft²
That's about 21,000 lb on every 1,000 ft² of roof.
Inside the typical residential design range (20–30 lb/ft²). Fine for most roofs in good condition — keep an eye on it if more snow is forecast.
Estimate only — not an engineering calculation. Based on the ASCE 7 ground-to-roof method with simplified exposure and slope factors. If in doubt, ask a structural engineer.
How much does snow weigh?
It depends on the snow. Fresh powder is mostly air; a settled pack is far denser; wet snow and ice are heavier still. Per inch of depth, on every square foot of roof:
| Snow type | Weight per inch of depth | 12 inches weighs |
|---|---|---|
| Fresh, light snow | ≈ 0.5 lb/ft² | ≈ 6 lb/ft² |
| Settled / packed snow | ≈ 1.3 lb/ft² | ≈ 15 lb/ft² |
| Wet, heavy snow | ≈ 2.1 lb/ft² | ≈ 25 lb/ft² |
| Ice layer | ≈ 4.8 lb/ft² | ≈ 57 lb/ft² |
That is why a harmless-looking foot of wet snow can outweigh two feet of powder — and why rain falling on an existing snowpack is the classic overload scenario: the pack absorbs the rain like a sponge instead of shedding it.
How to calculate roof snow load: the ASCE 7 method
Engineers design roofs using ASCE 7, the US loading standard. It starts from the ground snow load (pg) for your location — mapped by ASCE from decades of records, from near zero in the deep South to 100 lb/ft² or more in mountain snowbelts — then converts it to a flat-roof load: pf = 0.7 × Ce × Ct × I × pg. Ce adjusts for how sheltered or windswept the roof is, Ct for roof warmth (a heated home melts the bottom layer), and I for the building's importance. Sloped roofs then get a slope factor (Cs) because steeper roofs shed snow. Our calculator uses that same method with simplified, clearly-labelled factors and typical residential values (Ct = I = 1.0). You can look up your area's values with the ASCE hazard tool or your local building department. This is an estimate for homeowners, not an engineering calculation.
How much snow can a roof hold?
Most modern homes in snow country are designed for a roof snow load of roughly 20–40 lb/ft², matched to the local ground snow load — a Minnesota roof is built for far more than a Virginia one. The danger cases are older roofs, flat or nearly flat roofs, roof additions built to a weaker standard, and loads that pile up unevenly: drifts against a wall or in a valley can double the local load while the rest of the roof looks fine. Warning signs that a roof is stressed:
- New cracks in ceilings or walls, especially around door frames.
- Doors or windows that suddenly stick or pop open on their own.
- A visible sag in the roofline or ceiling.
- Creaking, popping or groaning sounds from the structure.
- Leaks that appear during or right after a storm, not from rain.
When and how to clear snow from a roof
- Work from the ground with a roof rake — never climb onto a snow-loaded roof; it is slippery exactly where it is weakest.
- Clear after each big storm rather than letting layers stack and freeze together.
- Leave a thin layer (an inch or two) so the rake doesn't damage shingles.
- Watch for ice dams at the eaves: thick ice ridges that trap meltwater under the shingles.
- If the load estimate is in the heavy range, the roof is flat, or you see warning signs, hire a professional with the right equipment and insurance.
More winter-weather planning: check your snow day chance before the storm, and our snow melt calculator afterwards to see how long the pack will sit on the roof.
Frequently asked questions
How much snow weight can a typical roof hold?
Most modern homes in snowy regions are designed for about 20–40 lb/ft² of roof snow load, depending on local code. That equals roughly 2–4 feet of settled snow — but far less if the snow is wet or icy, which is why depth alone is a poor guide.
How do I find my ground snow load?
Ground snow load is set by location in the ASCE 7 maps and your local building code. Check the free ASCE hazard tool (hazards.atcouncil.org) with your address, or ask your municipal building department — they design permits to it every day.
Is wet snow heavier than dry snow?
Much heavier. Per inch of depth, wet snow weighs about four times as much as fresh powder, and an ice layer about nine times as much. A modest 8 inches of wet snow can load a roof like several feet of fluff.
What are the warning signs that a roof is overloaded?
New ceiling or wall cracks, doors sticking or popping open, a sagging roofline, creaking or popping sounds, and sudden leaks. Any of these during a heavy snow load warrants clearing the roof promptly and, if they persist, a structural engineer's inspection.
Should I shovel snow off my roof myself?
Use a roof rake from the ground, or hire a professional. Never climb onto a snow-covered roof: the surface is slippery, the structure may already be stressed, and falls are the most common snow-removal injury. Leave a thin layer to protect the shingles.
Does a steep roof hold less snow?
Yes. Slope lets snow slide off and gives wind more grip, so design standards apply a slope factor that reduces the assumed load as pitch increases. The flip side is drifting: snow that slides or blows off one section piles up in valleys and against walls, where the local load can be double the average.
About the SnowDayPlanner Team
The SnowDayPlanner Team runs the snow day prediction model behind this site, combining live forecast data — snowfall, ice, wind chill and timing — with the closing patterns of thousands of school districts and boards. We publish how the model works and how accurate it has been, and we refresh predictions through the night as forecasts change, so the score you check in the morning reflects the latest data.